Lap Timing & Performance Analysis

AiM Sports Solo 2 DL Data Logging Lap Timer THE BRAND NEW DATA-LOGGING GPS LAP TIMER FOR MOTORSPORTS The new Solo 2 DL receives data from two satellite constellations, GPS and Glonass; this is a huge step forward since it is unbelievably faster and more precise than the previous version. Power-on requires only a few seconds and lap times are calculated with a max 2/100 sec. of tolerance thanks to 10Hz GPS sampling. A sleek newly-designed case with easier-to-use metal buttons add a premium look and feel to the world's most popular data-logger and GPS lap timer. The screen can be back-lighted in one of the seven colors: ECU CONNECTION Solo 2 DL -- the Solo with an ECU connection -- has over a thousand ECU protocols in its database. Easily connect your Solo 2 DL to your ECU and get reams information with just one cable. In case your ECU protocol isn't in the database, no problem: an ECU Driver Builder is available in the included Race Studio 3 software, allowing you to create your protocol yourself. This gives you access to a huge amount of data from your car that can be overlaid with GPS data to create an incredibly powerful analysis and learning tool! Choose your ECU cable: OBD2: the standard vehicle diagnostic port beneath your dash supplies the Solo 2 DL with a wealth of information. This is the standard cable most people will use. CAN/RS232: the Solo 2 DL can be connected to your CAN Bus for an even richer, broader spectrum of information than OBD2. This cable can require a bit more know-how to connect, however. Coil RPM: the Solo 2 DL now features a digital input allowing to log RPM either from square wave signals (8-50 V each signal) or pulse signals (150-450 V ignition coil trigger – primary circuit). FIND YOUR TRACK QUICKLY Solo 2 DL has access to a database of more than 3,000 tracks all over the world! As soon as it switches on, the Solo 2 DL identifies its position, recognizes the starting line coordinates of the track, and is ready to start sampling lap times. If your track isn't in the database, no problem: the Solo 2 DL will automatically enter into autolearning mode, figures out the characteristics of the track, and starts lap-timing anyway. PREDICTIVE LAP TIME LEDS The new Solo 2 DL's predictive lap time engine is now even more reliable. And with configurable RGB LEDs, it will give you a clear, fast indication of how your current lap compares with your best possible lap. That's functionality you typically find only on expensive driver-coaching electronic aids; now it's at your fingertips with the Solo 2 DL! RACE MODE SELECTION Solo 2 DL can manage different types of races: Speed races in a closed circuit Point to-point races Regularity Performance tests (0-100 km/h etc.) In each of these configurations, Solo 2 DL gives the relevant information during the race/test along with powerful data review immediately after each session. WiFi & iPHONE CONNECTION WiFi communication with your laptop is easy, fast, and with no connectors or cables. It's the best way to configure your Solo 2 DL, manage the track database, and download lap data to your PC. Connect your Solo 2 DL to your iPhone for quick and easy data analysis, managing your track database, etc. SMARTYCAM INTEGRATION The perfect connection: the Solo 2 DL takes all the data from your ECU, merges it with GPS lap information, and transmits everything seamlessly to a SmartyCam HD or SmartyCam GP HD . The resulting video includes your ECU and lap data in a graphical overlay! Feel free to give us a call at (844) 438-7244 to discuss the cool new features and capabilities of AiM's latest, greatest compact datalogger/lap timer today!

AiM Sports Solo 2 Lap Timer The new Solo 2 from AiM receives data from two satellite constellations, GPS and Glonass. This is a huge step forward since it is substantially faster and more precise than the previous version. As a result, power-on requires only a few seconds and lap times are calculated with a max 0.02-second tolerance. A sleek new case with easier-to-use metal buttons give the new AiM Solo 2 a premium look and feel. Plus, the screen can be backlighted in one of seven available colors: Find Your Race Track The AiM Solo 2 has access to a database of more than 3,000 tracks all over the world! As soon as it switches on, the Solo 2 identifies its position, recognizes the starting line coordinates of the track, and is ready to start sampling lap times. If your track isn't in the database, no problem: the Solo 2 will automatically enter into autolearning mode, figures out the characteristics of the track, and starts lap-timing anyway. Predictive Lap Time LEDs Help Make You Faster The new Solo 2's predictive lap time engine is now even more reliable. And with configurable RGB LEDs, it will give you a clear, fast indication of how your current lap compares with your best possible lap. That's functionality you typically find only on expensive driver-coaching electronic aids -- now it's at your fingertips with the Solo 2! Race Mode Selection The AiM Solo 2 can manage different types of races, such as: Speed races in a closed circuit> Point to-point races> Regularity> Performance tests (0-100 km/h etc.)> In each of these configurations, Solo 2 gives the relevant information during the race/test along with powerful data review immediately after each session.> AiM Solo 2 On-Screen Data Review At the end of your session or race, you can quickly review key lap information right on the Solo 2 color TFT display. WiFi and iPhone Connectivity WiFi communication with your laptop is easy, fast, and with no connectors or cables. It's the best way to configure your Solo 2, manage the track database, and download lap data to your PC. Connect your Solo 2 to your iPhone for a quick and comfortable data analysis, managing your track database, etc.

AiM MXG 1.2 Large Color TFT 7" Dash & Data Logger The AiM MXG 1.2 data-logging dash represents a huge leap forward in racing display flexibility. The brilliant 800x480 pixel, 7.0" color TFT display frees you from the constraints of a single, factory-designed dash display. The MXG shows you the data you want, the way you want in brilliant, high-contrast color. The MXG 1.2 is a large, brilliant dashlogger designed to acquire and display data coming from your ECU, an internal accelerometer and gyro, the included GPS08 Module, analog/digital inputs and pre-defined math channels. Performance data acquired can be expanded by adding up to eight expansion modules (sold separately). The large 7" high-color display makes it perfect for installation in wider cockpits (like in touring and GT cars). CONFIGURABLE PAGES You can define all the custom pages you wish, choosing from a large library of page styles and colors, defining which data you want to see and where (including end of scale and units of measure). Swapping between pages is as easy as pushing one or two buttons! INPUT/OUTPUT FLEXIBILITY Eight fully configurable analog input channels can sample, log, and display a wide range of temperatures, pressures, and potentiometers (throttle position, steering wheel position, etc). CAN Inputs allow you to further expand the dash by adding an almost limitless number of AiM CAN Data Hubs (Part No. MC-329, sold separately). These hubs let you connect other inputs such as Lambda Controller (O2), SmartyCam, or even channel expansion hubs, without using any analog channels. A separate CAN Output allows you to send messages to the existing CAN network, adding to the vehicle system control possibilities! The MXG 1.2 can also be connected to many different ECUs to log data gathered by each ECU. An internal three-axis accelerometer, gyroscope, and magnetometer; GPS08 input; four wheel-speed channels; lap time receiver input; and two digital outputs add up to a flexible, expandable data logger that can grow with you. It even has a screw-in port to add analog cameras used for back-up or rear view in visibility-challenged race cars! ALARMS & SHIFT LIGHTS Flexible alarms on the MXG 1.2 include six configurable RGB alarm LEDs: you choose the conditions, you choose the colors. Select a solid alarm or flashing one - and the flashing frequency, choose to have an accompanying text message, and set the alarm priorities. The integrated shift light array features a host of advanced multicoloured RGB shift light patterns that can be customized as you like, including RPM max for each individual gear. DIGITAL OUTPUTS The MXG 1.2 features two digital outputs (low-side type, switch to ground) that can be configured to activate/deactivate external systems (switch on/off additionallights, cooling fan relays, fluid circulation pumps, etc.) based on those inputs. MEMORY & WIFI CONNECTIVITY The 4GB non-volatile memory can store hours of information for detailed analysis using AiM's latest Race Studio 3 software. A secure 802.11 WiFi connection makes it even more convenient to configure, calibrate, and download your data wirelessly! No more need to move your PC close to the vehicle, you can do it from your trailer or tow vehicle up to 60 yards away. FEATURES & SPECS: 9.3" x 5.0" x 1.0" Anodized Aluminum housing Large 7.0" high-contrast color TFT display 800x480 pixel screen resolution Internal 4GB memory Two Motorsports and one Binder connector Weight 2.1 lbs (950g) Waterproof IP65 KIT INCLUDES: MXG 1.2 data logging dash GPS08 Module with cable USB cable wiring harness with 37 pin Deutsch connector installation CD with Race Studio 3 software All other sensors and modules sold separately.

AiM MXP 50% Bigger Display Than MXS In Similar-Sized Package This brilliant dash logger from AiM features a stunning high-contrast color 6" TFT display, an integrated LED shift array, configurable multicolor LED alarms, drag and drop multi page configuration, Wi-Fi and USB connectivity, included GPS08 Module, inertial platform, analog and digital inputs, digital outputs, Motorsport connectors, 4 GB of internal memory, 1,000Hz per channel sampling and support for over 1,000 ECU connections! That all adds up to an incredibly flexible, powerful, and useable information center at your fingertips in your race car. WIDE RANGE OF DATA SOURCES The AiM MXP samples data coming from your ECU, the GPS Module, its internal nine-axis inertial platform (accelerometer, gyro and magnetometer), eight fully configurable analog inputs, six digital inputs, predefined math channels and a second CAN. Performance info and data acquired can be expanded by adding up to eight expansion modules. CONFIGURABLE PAGES You can define all the custom pages you wish, choosing from a wide library of page styles, defining which data to be shown, their end of scale and units of measure. Swapping between pages is as simple as pushing one or two buttons! FLEXIBLE ALARMS AND ICONS The MXP features five configurable RGB alarm LEDs: you choose the conditions, you choose the colors. Select a solid alarm or flashing one (and the flashing frequency), choose to have an accompanying text message, and set alarm priorities. You can also choose the street icons you need from a large list in Race Studio 3 - Icons Management, then set them up any way you prefer. They're all fully configurable, and if that's not enough, you can upload and set-up your own customized icons! TWIN DIGITAL OUTPUTS MXP features two digital outputs. They can be configured to respond to the analog or digital inputs to automatically run external systems (e.g. to switch on/off additional lights, activate/de-activate a cooling fan or fluid circulation pumps, etc.) DUAL CAMERA INPUTS Two analog camera inputs are available to swap your display into a mirror camera or rear-view camera through either push button command or in response to certain programmable events. Especially useful in a race car with limited visibility/sightlines. SHIFT LIGHT ARRAY Choose from a host of advanced multicolored RGB shift light patterns that can be customized as you like, including RPM settings for each individual gear. WiFi CONNECTIVITY It's so convenient to configure, calibrate, and download your data wirelessly using a secure 802.11 WiFi connection. No need to move your PC close to the vehicle anymore, you can do it from your trailer or tow vehicle up to 60 yards away. KEY FEATURES & SPECS: Midsized 6" high-contrast color TFT display 800x480 pixel screen resolution 7.5" x 4.2" x 1.0" anodized aluminum housing Three CAN connections 15 configurable RGB LEDs Weight 1.4 lbs (640g) 4GB internal memory Waterproof IP65 KIT INCLUDES: AiM MXP dashlogger GPS08 Module with cable USB cable 37-pin Deutsch connector harness Installation CD with Race Studio 3 software

The Compact Color TFT Dash For Road Use WIDE RANGE OF DATA & DISPLAYS MXS 1.3 Strada is a beautifully-designed, feature-rich color digital dash display. It is basically the MXS 1.3 without the datalogging function. The MXS 1.3 Strada features a compact 5" High Contrast TFT color screen with great visual impact, configurable to show lap times, RPM, and a huge range of info coming from your Engine Control Unit, analog/digital inputs, pre-defined math channels and an optional GPS08 Module. Programmable multicolor shift and alarm LEDs round out an incredibly powerful package. There's even a version with "Street Icon" LEDs instead of the traditional "plain" LEDs! The MXS 1.3 Strada displays your RPM, selected gear, speed, plus all the data you choose (water temp, oil pressure, trans temp, lap times and much more) in either pre-configured or user-customized pages. Swapping between pages is as easy as pushing buttons. Plus the MXS 1.3 Strada puts a huge amount of control over your car's systems at your fingertips. INPUT & OUTPUT FLEXIBILITY Eight fully configurable analog input channels can sample, log, and display a wide range of temperatures, pressures, and potentiometers (throttle position, steering wheel position, etc). Choose between OBDII and CAN/RS232 versions to suit your needs and level of customization. Both receive rich data from your ECU. An OBDII input connection is an easy, plug-and-play option. A hardwired CAN input allows you to further expand the dash by adding an almost limitless number of AiM CAN Data Hubs (Part No. MC-329, sold separately). These hubs let you connect other inputs such as Lambda Controller (O2), SmartyCam, or even channel expansion hubs, without using any analog channels. A separate CAN output allows you to send messages to your car's existing CAN network, adding to the vehicle system control possibilities! ALARMS & SHIFT LIGHTS The ten multicolored RGB shift lights can be customized to define the max RPM for each single gear. The same flexibility applies to the configurable RGB alarm LEDs: you can configure them to turn on/off depending on analog or digital inputs, ECU values, expansion values, math channels or GPS information (with the optional GPS08). You choose conditions, colors, and select a solid alarm or flashing one (including flash frequency). It's also possible to configure an accompanying text message. DIGITAL OUTPUT The MXS 1.3 Strada features a low-side (switch to ground) digital output that can be configured to activate/deactivate external systems (switch on/off additional lights, cooling fan relays, fluid circulation pumps, etc.) based on those inputs. RACE STUDIO 3 INTEGRATION MXS 1.3 Strada is configured using your PC and Race Studio 3. You can create, customize, delete, import and export configurations with all channels, ECU drivers, Math Channels, Display Pages, Digital Output, Alarms, Shift Lights and all the expansions you need. TECHNICAL SPECS: Compact 6.7" x 3.8" x 0.9" anodized aluminum housing 5" TFT high-contrast color display Choose Standard or Street Icon LEDs Screen resolution 800x480 pixels Weight 1 lb. (480g) Waterproof IP65 KIT INCLUDES: MXS 1.3 Strada digital dash USB cable 14-pin standard wiring 23-pin Connector + contacts Installation CD with Race Studio 3 software All sensors and modules sold separately.

AiM MXS 1.2 Color TFT 5" Dash And Data Logger Check Out The MX Series User Manual Here The MXS 1.2, the evolution of MXS, is a beautifully executed compact dash/data logger designed to put data at your fingertips. It can acquire data from your ECU, its internal accelerometer and gyro, the included GPS08 Module, analog/digital inputs and pre-defined math channels. The incredibly sharp, full-color TFT display puts it all front-and-center, in incredible color with a high contrast ratio. It even automatically adjusts its backlight based on ambient light to optimize visibility. Freely configurable pages let you define all the custom pages you wish, choosing from a wide library of page styles and defining which data to display, their end of scale and units of measure. Swapping between pages is as easy as pushing a button! GPS08 Thanks to the included GPS08 Module and AiM's Race Studio 3 software, you can immediately get lap times along with all data needed for engine tuning, shaking down car and driver, and for improving and refining driving technique. A MULTITUDE OF DISPLAYS The MXS 1.2 displays your RPM scale plus all the data you need (speed, water temp, oil pressure, lap times and much more) in pre-configured pages. Or you can customize pages as you wish, choosing from a wide library of page styles and defining which data to be shown, their end of scale and measure units. Swapping between pages is quite easy using push buttons. A 4GB non-volatile memory stores hours of information for detailed analysis using AiM's Race Studio 3 software. All data can be downloaded to your computer using a built-in secure Wi-Fi connection (no cable required). LOTS OF INPUT/OUTPUT FLEXIBILITY Eight fully configurable analog input channels can sample, log, and display a wide range of temperatures, pressures, and potentiometers (throttle position, steering wheel position, etc). CAN Inputs allow you to further expand the dash by adding an almost limitless number of AiM CAN Data Hubs (Part No. MC-329, sold separately). These hubs let you connect other inputs such as Lambda Controller (O2), SmartyCam, or even channel expansion hubs, without using any analog channels. A separate CAN Output allows you to send messages to the existing CAN network, adding to the vehicle system control possibilities! The MXS 1.2 can also be connected to many different ECUs to log data gathered by each ECU. An internal three-axis accelerometer, gyroscope, and magnetometer; GPS08 input; four wheel-speed channels; lap time receiver input; and two digital outputs add up to a flexible, expandable data logger that can grow with you. It even has a screw-in port to add analog cameras used for back-up or rear view in visibility-challenged race cars! SHIFT LIGHTS & ALARMS Flexible alarms on the MXS 1.2 include six configurable RGB alarm LEDs: you choose the conditions, you choose the colors. Select a solid alarm or flashing one - and the flashing frequency, choose to have an accompanying text message, and set the alarm priorities. The integrated shift light array features a host of advanced multicoloured RGB shift light patterns that can be customized as you like, including RPM max for each individual gear. DIGITAL OUTPUTS The MXS 1.2 features two digital outputs (low-side type, switch to ground) that can be configured to activate/deactivate external systems (switch on/off additional lights, cooling fan relays, fluid circulation pumps, etc.) based on those inputs. WiFi CONNECTIVITY A secure 802.11 WiFi connection makes it even more convenient to configure, calibrate, and download your data wirelessly! No need to move your PC close to the vehicle anymore, you can do it from your trailer or tow vehicle up to 60 yards away. TECHNICAL SPECS: Compact 6.7" x 3.8" x 0.9" anodized aluminum housing 5" TFT high-contrast color display Internal 4GB memory Screen resolution 800x480 pixels Two Motorsport connectors and one Binder connector Weight 1.2 lb. (530g) Waterproof IP65 KIT INCLUDES: MXS 1.2 Unit GPS08 Module with cable USB cable 37-pin standard Deutsch-connector harness Software installation CD with Race Studio 3 software. All other sensors and modules sold separately.

AiM Sports MXm Compact Dash Logger The new MXm from AiM is the compact dash logger with big features to put all the information you need right at your fingertips. It samples and shows key info like speed, lap times, RPM, gears, data from a nine-axis inertial platform, multiple math channels and much more. It is compact (5.4 x 3.5 x 1.3 in.), making it perfect for sports cars and bikes, and it's plug-and-play for ease-of-use. Complete but simple, MXm is the perfect device for both Pro and Amateur drivers. WIDE RANGE OF DATA SOURCES MXm samples data from your ECU, its internal GPS and inertial platform (accelerometer, gyro and magnetometer), four fully configurable analog inputs, three digital inputs (two speed + one coil RPM input), and predefined math channels. For the most demanding, the MXm can be connected to the Lambda controller and a SmartyCam HD to create a fully-integrated AiM information suite. INTEGRATED SHIFT LIGHTS & ALARM MXm features a five-LED shift light array. Choose from a host of advanced multicolored RGB shift light patterns that can be customized to your needs, and for each unique gear when required. MXm also features two fully configurable RGB alarm LEDs: you can choose the conditions that turn them on/off, their color, and select a solid alarm or flashing one (and the flash frequency.) DUAL POWER OUTLETS MXm features two power outputs that can supply up to 15A each. These outputs can turn on/off depending on the value of analog or digital inputs to the MXm. They can automatically actuate external systems, such as switching on/off additional lights, activating/de-activating cooling fans or circulation pumps, etc. SHARP LCD MXm features a high contrast LCD display with an outstanding black to white ratio. The wide 268 x 128-pixel graphical LCD offers great flexibility in information display and alerts. The screen can be backlighted in one of the seven available colors, and an ambient light sensor keeps the backlight at optimum brightness. CUSTOMIZABLE LAYOUT You can organize the huge quantity of data captured by MXm into your own custom pages, choosing from a wide range of page styles, data to be shown, their end of scale and unit of measure. At the end of each session, you can review an on-screen summary of your best laps, max/min RPM, speed and temperatures. WIFI CONNECTIVITY Makes it even more convenient to configure, calibrate, and download your data wirelessly, using a secure 802.11 connection. No need to move your PC close to the vehicle anymore, you can do it from your trailer up to 50 yards away. SMARTYCAM COMPATIBILITY SmartyCam on-board cameras, for professional recording of your races, with your real-time data overlayed on videos. RACE STUDIO 3 DATA ANALYSIS Race Studio 3 is the true engine of your MXm. With Race Studio 3, you can analyze all data recorded by MXm and downloaded to your PC. RS3 generates graphs, histograms, and tables to help you study your performance, providing an objective support to correct mistakes and improve your driving. You can even compare two laps watching the video recorded by SmartyCam HD cameras! RS3 can create, modify, delete, import and export MXm configurations with all channels, ECU drivers, math channels, display pages, digital outputs, alarms, shift lights and expansions.

AiM MXT 1.3 Logger with GPS Ready to elevate your racing game? Meet the AiM MXT 1.3 Logger with GPS – the ultimate data logging dash that transforms your track day into a high-tech mission. This bad boy isn't just a dashboard; it's your new best friend on the circuit. Features And Benefits Flexibility and Customization Galore: The AiM MXT 1.3 boasts an extra-large 1280x480 pixel (10" diagonal) TFT display, breaking free from the boring, factory-designed LCDs. Want your data your way? You got it! The customizable screen lets you set up eight different pages with unique designs. Data Overload (In the Best Way): With eight analog input channels, you can sample, log, and display a wide array of temperatures, pressures, and potentiometers (think throttle and steering positions). And that's just the start. A CAN input allows endless expansion with AiM CAN Data Hubs (sold separately). Connect Lambda (O2) sensors, SmartyCam, or even more channels without using analog inputs! Ultimate Compatibility: Hook up to multiple ECUs to log any data your engine management system gathers. The MXT 1.3 also includes an internal gyroscope, 3-axis g-sensor, GPS module, four-wheel speed channels, a lap time receiver input, and two digital outputs. It's a data-logging beast that grows with you. Visual Delight: Housed in a sleek, anodized aluminum frame (10.94" x 5.3"), the 9.6" x 3.6" screen auto-dims to match your environment. Configure ten shift light LEDs and six alarm LEDs to flash in any of seven colors, triggered by your custom conditions. Set shift lights for each gear, choose colors, and more! Rear-View Magic: An extra port lets you connect analog cameras to use the dash as a backup or rear-view mirror display. Note: this doesn't work with the SmartyCam, but it's perfect for other cameras. Massive Storage and Easy Downloads: With 4GB of non-volatile memory, store hours of race data for deep dives later. Download everything to your computer using the built-in secure Wi-Fi – no cables needed. What’s in the Box? The MXT 1.3 data logging display, wiring harness with a 37-pin Deutsch connector, and the GPS09 module. Note: All sensors are sold separately, and for additional connections, you’ll need the AiM MX-Series Auxiliary Wiring Harness with 22-Pin Deutsch Connector (also sold separately). Product Specifications: Display: 1280x480 pixel (10" diagonal) TFT Housing: 10.94" x 5.3" anodized aluminum Channels: 8 analog inputs, 1 CAN input Sensors: Internal gyroscope, 3-axis g-sensor, GPS module, 4 wheel speed channels Memory: 4GB non-volatile Connectivity: Secure Wi-Fi, 2 digital outputs Power Supply: 9 - 15V external FAQs Q: Can the MXT 1.3 connect to my car's ECU? A: Absolutely! The MXT 1.3 can connect to a wide range of ECUs to log any data collected by the engine control unit. Q: How many pages can I customize on the display? A: You can create up to eight different pages, each with its unique screen design. Q: Do I need a separate power supply? A: Yes, the MXT 1.3 requires a 9 - 15V external power supply. Q: Is the SmartyCam compatible with the camera input port? A: No, the extra port on the MXT 1.3 is not compatible with the SmartyCam. It’s designed for other analog cameras. Q: What do I need for additional connections? A: For analog channels 5-8, speed inputs 2-4, digital outputs, and RS232 ECU connection, you’ll need the AiM MX-Series Auxiliary Wiring Harness with 22-Pin Deutsch Connector (sold separately). Ready to dominate the track? The AiM MXT 1.3 Logger with GPS is your ticket to precision, performance, and endless customization. Don’t just drive – thrive. Grab yours today and leave your competition in the dust! Call To Action: Don’t wait – gear up for your next race with the AiM MXT 1.3 Logger with GPS. Click "Add to Cart" now and transform your driving experience! All other sensors and modules sold separately.

Garmin Catalyst 2 Race Track Driving Performance Optimizer SHIPPING NOW Designed with a bright 3-inch display and a built-in camera, Garmin Catalyst 2 easily mounts on the windshield and brings on-track coaching features to the cockpit, including Garmin's unique True Optimal Lap, which shows drivers their best achievable time with a composite video of lines they drove. It also features real-time audio cues and post-session comparison of performance data to help drivers see where they can gain time. DISCOVER YOUR FULL TRACK DRIVING POTENTIAL Designed as a compact, windscreen-mounted unit, the Garmin Catalyst 2 features a 3-inch display and an integrated camera capable of recording 1440p high-definition video. The idea is simple enough: capture what the car is doing on track, analyze it automatically, and feed that information back to the driver in a format that is easy to act on to improve lap times. Garmin Catalyst 2 includes unique motorsports coaching features that can help drivers improve on the track. After a track session, drivers can open the Garmin Catalyst app on a compatible smartphone or tablet to review detailed performance analysis, driver comparison data and more. True Optimal Lap: Patented Garmin technology splices together a driver's best achievable time into a single video based on lines driven if all best lines had been driven on the same lap. On-track coaching: Receive real-time coaching with audio cues for speed, braking and more – heard through connected earbuds or the car stereo. Automatic data interpretation: See the top three opportunities for improvement after every session, allowing drivers to spend less time analyzing previous laps and more time on the track. Leaderboards: Drivers can see how they stack up against other drivers with best lap times sortable by session, day, year, car make or model. Video with data overlays: View graphic overlays on 1440p high-definition videos, which include track map, speed, delta time, G-G traction circle diagrams and more2. Detailed performance data: See animated graphs2, comprehensive driving information and friend comparisons. Enhanced data accuracy: Refined True Track Positioning™ uses built-in accelerometers, gyroscopes, image processing and 25 Hz multi-GNSS positioning for recording the most precise racing line on the track. Vault storage: With an active Vault plan, optimal and best lap videos are automatically saved and accessible through the Garmin Catalyst app. This makes it easy for users to view and share videos and allows them to manually store laps or sessions for as long as their plan is active. Overview At the center of the system is Garmin’s True Optimal Lap technology. This patented feature pieces together a driver’s best theoretical lap by combining the quickest segments and lines they have driven across multiple laps into a single composite video. Rather than showing what was achieved, it presents what was possible if every best sector had been strung together in one go. Positioning accuracy has been upgraded through Garmin’s True Track Positioning system, which uses built-in accelerometers, gyroscopes, image processing and 25 Hz multi-GNSS data to record racing lines with greater precision. Display & Audio Catalyst uses a 3" touch screen with vivid TFT colors. The LCD is a touchscreen, able to control functions without the need for a remote control, app, or a laptop. Coaching or playback audio is available via 3.5mm headphone jack or Bluetooth(TM) to your headset or car stereo.  Coaching On-track coaching is delivered via real-time audio prompts, which can be played through connected earbuds or the car’s stereo. Drivers receive cues on speed, braking and other key inputs while circulating, something Gamin claims will reduce the amount of post-session guesswork.  In addition to circuit use, the Catalyst 2 now includes a drag racing timer, recording 0–60mph, 1/8-mile and 1/4-mile times for those heading to the strip. Analysis & Review After each session, the device automatically identifies what Garmin describes as the top three areas for improvement. If drivers want to drill down further into the data, more detailed analysis is available through the companion app. Here, users can review performance data, compare laps and access animated graphs. Video footage can be viewed with data overlays including track maps, speed traces, delta times and G-force traction circle diagrams. Leaderboards allow drivers to compare best lap times by session, day, year, or even by car make and model. An optional Vault subscription automatically stores optimal and best lap videos in the cloud via the Garmin Catalyst app, making them accessible for later review - probably when you are boasting to your buddies about how much faster you are! GARMIN CATALYST 2 RACETRACK DRIVING PERFORMANCE OPTIMIZER DETAILS Manufacturer: Garmin Manufacturer part no: 010-03924-00 Dimensions:  Display size: 3" touchscreen Touch screen: yes Weight:  Battery: rechargeable lithium-ion Battery life: up to [ ] hours Internal memory: Includes mount: yes GPS: yes GLONASS: yes 25Hz multi-GNSS positioning: yes Garmin Connect compatible: yes Included camera: yes Camera resolution: 1440p Camera field-of-view: 140º Camera frame rate:  [ ] fps Software & track database updates included Bluetooth connectivity: yes In the Box with your Garmin Catalyst Garmin Catalyst Continue reading to see how and why the Garmin Catalyst Driving Performance Optimizer is unlike anything you've ever experienced. Heck... it's unlike anything you've ever even thought possible!