Competition Motorsport
CMS Performance RF1 DOT4 Racing Brake Fluid (500 ml)
from $24.95
CMS Performance RF1 DOT4 622oF Racing Brake Fluid
Buy in bulk and save. Get six bottles and save 15%, or a case of 12 and save a whopping 25%!
The Highest Dry Boiling Point Racing Brake Fluid You Can Buy
CMS Performance RF1 fully synthetic Racing Brake Fluid is formulated to provide the highest performance under racing and track-day conditions, where braking systems operate at very high sustained temperatures. RF1 exceeds all DOT 3 & 4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.)
There is perhaps no single safety system more important in racing than brakes. And no part of that system is more critical than brake fluid. At Competition Motorsport, we got tired of (and a little nervous) using "racing" brake fluid on the track that didn't live up to its claimed performance.
So we did something about it. Manufactured in partnership with Orthene Chemicals, a British brake fluid supplier to professional race teams in Formula 1, WEC, and many other pro series, CMS Performance RF1 Racing Brake Fluid is formulated to maintain consistent viscosity, lubricity, and compressibility at extreme temperatures and line pressures found in racing, track days, and spirited driving.
Bottom line: you can spend more money, but you can't buy higher-performing racing brake fluid!
CMS Performance RF1 Racing Brake Fluid Specifications:
Typical dry boiling point: 622° F (328° C)
Typical wet boiling point: 399° F (204° C)
Exceeds DOT3 & DOT4 standards
Individual 500 ml (16.7 oz.) bottles
Click Here For The RF1 Product MSDS Sheet
A Note About Brake Fluid Boiling Points
DOT 4 brake fluid like RF1 is hygroscopic, meaning it attracts water over time sitting in your brake lines and reservoir. At high brake temperatures, this water can boil in your car's brake lines, causing the fluid in the lines to become compressible. That's what you feel when you experience brake fade. This is why the "wet" (aged fluid) boiling point of any brake fluid is substantially lower than the "dry" (brand new fluid) boiling point.
Since time is the enemy of brake fluid performance, the best practice is to replace your racing brake fluid before each track event/weekend. At a minimum, flush it with new fluid at least every three months if you're consistently racing and/or driving at track days. A couple bottles of fluid will flush most sports cars or race cars. It ends up being pretty cheap insurance against learning about brake fade the hard way.
Girodisc
Girodisc Pad Spreader GDPS01
$250.00
Girodisc Brake Pad Spreader
This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The spreader is designed to spread brake pads and pistons in four- and six-piston calipers to facilitate quick replacement of pads and/or rotors in a shop or racing environment.No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons evenly and all the way back into their bores with one squeeze of the levers. The Girodisc spreader was designed around popular four-piston and six-piston calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help fit in any caliper, the amount of throw is adjustable.Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.The Girodisc Pad Spreader is made from heavy-gauge steel and is powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors with any frequency.
Girodisc
A1-102 Girodisc 2pc Front Brake Rotors
$1,900.00
Thunderhill is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline.
Fits Ferrari 430 Challenge
The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response.
When used with Pagid or PFC performance brake pads, and Thunderhill RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors.
The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling.
Sold/Priced per pair.
Girodisc
A2-102 Girodisc 2pc Rear Brake Rotors
$1,800.00
Thunderhill is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline.
Fits Ferrari 430 Challenge
The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response.
When used with Pagid or PFC performance brake pads, and Thunderhill RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors.
The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling.
Sold/Priced per pair.
Girodisc
D1-102 Girodisc Front Replacement Rotor Rings
$950.00
FITS: FERRARI 430 CHALLENGE
REPLACEMENT ROTOR DISC ONLY, DOES NOT INCLUDE ALUMINUM HAT.
Thunderhill is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline.
The GiroDisc replacement rotor system is a direct rotor disc replacement for the Giro Disc 2-piece hat and rotor and no modifications are necessary.
The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The 2-piece GiroDisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling.
Sold/Priced per pair.
Girodisc
D2-102 Girodisc Rear Replacement Rotor Rings
$950.00
FITS: FERRARI 430 CHALLENGE
REPLACEMENT ROTOR DISC ONLY, DOES NOT INCLUDE ALUMINUM HAT.
Thunderhill is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline.
The GiroDisc replacement rotor system is a direct rotor disc replacement for the Giro Disc 2-piece hat and rotor and no modifications are necessary.
The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The 2-piece GiroDisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling.
Sold/Priced per pair.
Pagid
Pagid Racing Brake Pads No. 4906
from $497.86
Fits These Vehicles:
Make
Model
Build (Year)
Front
Rear
Chevrolet
Camaro Z28 [ceramic brakes]
15 -
X
Chevrolet
Corvette Brembo [ceramic brakes]
09 -
X
Chevrolet
Corvette C7 Z06 [ceramic brakes]
15 -
X
Dodge
Viper ACR [ceramic brakes]
16 -
X
Ferrari
360 Challenge Stradale [ceramic brakes]
03 - 05
X
Ferrari
430 Challenge [ceramic brakes]
X
Ferrari
430 Scuderia [ceramic brakes]
07 - 10
X
Ferrari
458 Italia [ceramic brakes]
10 - 15
X
Ferrari
599 GTB Fiorano
06 - 12
X
Ferrari
Enzo [ceramic brakes]
02 - 04
X
Ferrari
F430 [ceramic brakes]
05 - 10
X
Ferrari
Several ceramic brakes CCM
X
Lamborghini
Aventador LP700-4 [ceramic brakes]
11 -
X
Lamborghini
Several ceramic brakes
X
RSC 1:
RSC1 is a good street/track compromise for enthusiasts with carbon-ceramic brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.
RSC 2:
The Pagid RSC2 is a special race compound for ceramic discs with a high content of fibers in the friction surface. A medium-high friction pad with excellent fade resistance and long pad life, developed for sprint and endurance circuit racing.
RSC 3:
The Pagid RSC3 is a high-friction compound developed for ceramic discs. With a high initial bite, strong fade resistance, and slightly shorter pad life than the RSC2, this is Pagid's more aggressive ceramic-rotor racing pad.
Pagid
Pagid Racing Brake Pads No. 8091
from $684.41
Fits These Vehicles
Make
Model
Build (Year)
Front
Rear
Chevrolet
Camaro Z28 [ceramic brakes]
15 -
X
Chevrolet
Corvette Brembo 6 piston non ceramic
09 -
X
Chevrolet
Corvette Brembo [ceramic brakes]
09 -
X
Chevrolet
Corvette C7 Z06 [ceramic brakes]
15 -
X
Ferrari
430 Challenge [ceramic brakes]
X
Ferrari
430 Scuderia [ceramic brakes]
07 - 10
X
Ferrari
458 Italia [ceramic brakes]
10 - 15
X
Ferrari
599 GTB Fiorano
06 - 12
X
Ferrari
Several ceramic brakes CCM
X
McLaren
570 S [ceramic brakes]
15 -
X
McLaren
650 S [ceramic brakes]
14 -
X
McLaren
675 LT [ceramic brakes]
15 -
X
McLaren
MP4-12C [ceramic brakes]
11 - 14
X
RSL 19:
The PAGID RSL19 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RSL19 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear.
RSC 1:
The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.
RSC 2:
The Pagid RSC2 is a special race compound for ceramic discs with a high content of fibers in the friction surface. A medium-high friction pad with excellent fade resistance and long pad life, developed for sprint and endurance circuit racing.
RSC 3:
The Pagid RSC3 is a high-friction compound developed for ceramic discs. With a high initial bite, strong fade resistance, and slightly shorter pad life than the RSC2, this is Pagid's more aggressive ceramic-rotor racing pad.
Sign Up and Save
Subscribe to our eNewsletter to learn about events near you, great deals, new products and for tips to improve your creator skills.